Siemens FC300 Operating Instructions Manual Download Page 38 | Manualshive

Page: 38 / 518

Siemens FC300 Operating Instructions Manual Download Page 38

WARNING

Exceeded maximum permissible operating pressure
Risk of injury or poisoning.
The maximum permissible operating pressure depends on the device version, pressure limit

and temperature rating. The device can be damaged if the operating pressure is exceeded.

Hot, toxic and corrosive process media could be released.
Ensure that maximum permissible operating pressure of the device is not exceeded. Refer

to the information on the nameplate and/or in Technical data (Page 215).

WARNING

Unprotected cable ends
Risk of explosion through unprotected cable ends in hazardous areas.
● Protect unused cable ends in accordance with IEC/EN 60079-14.

WARNING

Incorrect mounting at Zone 0
Risk of explosion in hazardous areas.
● Ensure sufficient tightness at the process connection.
● Observe the standard IEC/EN 60079-14.

WARNING

Loss of explosion protection
Risk of explosion in hazardous areas if the device is open or not properly closed.
● Close the device as described in Installing/mounting (Page 37).

CAUTION

External stresses and loads
Damage to device by severe external stresses and loads (e.g. thermal expansion or pipe

tension). Process media can be released.
● Prevent severe external stresses and loads from acting on the device.

Installing/mounting
4.1 Basic safety notes

MASS 2100 & FC300 (FCT030)

38

Operating Instructions, 06/2017, A5E39789040-AA

«
...
36
37
38
39
40
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments