manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 57 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 57

Connecting

5

5.1

Basic safety notes

WARNING

Unsuitable cables, cable glands and/or plugs
Risk of explosion in hazardous areas.
● Use only cable glands/plugs that comply with the requirements for the relevant type of 

protection.

● Tighten the cable glands in accordance with the torques specified in Technical data 

(Page 215).

● Close unused cable inlets for the electrical connections.
● When replacing cable glands use only cable glands of the same type.
● After installation check that the cables are seated firmly.

WARNING

Incorrect conduit system
Risk of explosion in hazardous areas as result of open cable inlet or incorrect conduit system.
● In the case of a conduit system, mount a spark barrier at a defined distance from the device 

input. Observe national regulations and the requirements stated in the relevant approvals.

WARNING

Hazardous contact voltage
Risk of electric shock in case of incorrect connection.
● For the electrical connection specifications, refer to the information in Technical data 

(Page 215).

● At the mounting location of the device observe the applicable directives and laws for 

installation of electrical power installations with rated voltages below 1000 V.

NOTICE
Condensation in the device
Damage to device through formation of condensation if the temperature difference between 

transportation or storage and the mounting location exceeds 20 °C (36 °F).
● Before taking the device into operation let the device adapt for several hours in the new 

environment.

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

57

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments