Ricoh Ri 100 Operating Instructions Manual Download Page 212 | Manualshive

Page: 212 / 260

background image

See page 104 "Printing".

The cassette is incorrectly loaded

The cassette is not pushed to the back.

Place the rear side of the cassette on the cassette stand, and then slowly push it in all the way until it
clicks.
See page 72 "Loading Fabrics".

The position of the cassette is too high.

A height position sensor in the machine is reacting. Remove the cassette and reload the fabric correctly,
and then reload the cassette. If printing does not start, adjust the height of the cassette.
See page 72 "Loading Fabrics", page 210 "Adjusting the Height of the Cassette".

The position of the detection lever for the multi tray does not match the one specified by the
settings of the printer driver.

Switch the detection lever for the type of cassette or attachment you want to use.
See page 75 "Loading a Fabric in the Multi Tray", page 77 "Loading a Sleeve in the Multi Tray".

Foreign objects remain inside the machine

Remove the cassette and find foreign objects inside the machine.

Adjusting the Height of the Cassette

Normally, the height of the cassette is automatically adjusted at the start of printing, but you can adjust
the height of the cassette using the [Adjust Height ] key or the [Maintenance] menu. This section
explains how to adjust the height of the cassette using the [Adjust Height ] key to resolve the problem
caused by the height position sensor reacting after the machine starts printing. For details about
adjusting the height of the cassette using the [Maintenance] menu to improve the image quality, see
page 211 "Adjusting the height of the cassette manually".
If wrinkles, slacks, or floats remain on the fabric or dust or similar objects are attached, the height
position sensor reacts and printing may not start. If this is the case, remove the cassette and reload the
fabric correctly, and then reload the cassette.
See page 72 "Loading Fabrics".
If an error message appears even after the cassette is loaded and printing does not start, adjust the
height of the cassette as follows:

9. Troubleshooting

210

«
...
210
211
212
213
214
...
»

Summary of Contents for Ri 100





































































































































































































































































Reviews:

No comments

Related manuals for Ri 100

EasyCoder 501 SA

Brand: UBI Pages: 214

Brand: UBI Pages: 64

imageRUNNER 2545i

Brand: Canon Pages: 37

Brand: imagistics Pages: 57

Brand: Ricoh Pages: 2

Brand: Oki Pages: 120

Brand: Konica Minolta Pages: 44

Brand: SAGEMCOM Pages: 146

4400B - Phaser B/W Laser Printer

Brand: Xerox Pages: 24

ColourLaser 21 Series

Brand: Xante Pages: 32

Brand: Sartorius Pages: 202

E-Class Mark III

Brand: datamax-o'neli Pages: 58

Brand: Savin Pages: 90

Brand: Perel Pages: 13

Brand: CAB Pages: 222

Brand: Sharp Pages: 46

Brand: Sharp Pages: 36

Brand: Sharp Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands