Ricoh Ri 100 Operating Instructions Manual Download Page 40

Page: 40 / 260

Plugging in the Power Cord and Turning the

Power On

Before connecting the machine to a computer, connect the machine's power cord and turn the machine
on.

• Do not use any power sources other than those that match the specifications shown in this

manual. Doing so could result in fire or electric shock.

• Do not use any frequencies other than those that match the specifications shown. Doing so could

result in fire or electric shock.

• Do not use multi-socket adaptors. Doing so could result in fire or electric shock.

• Do not use extension cords. Doing so could result in fire or electric shock.

• Do not use power cords that are damaged, broken, or modified. Also, do not use power cords

that have been trapped under heavy objects, pulled hard, or bent severely. Doing so could
result in fire or electric shock.

• Touching the prongs of the power cable's plug with anything metallic constitutes a fire and

electric shock hazard.

• It is dangerous to handle the power cord plug with wet hands. Doing so could result in electric

shock.

• The supplied power cord is for use with this machine only. Do not use it with other appliances.

Doing so could result in fire or electric shock.

• If the power cord is damaged and its inner wires are exposed or broken, contact your service

representative for a replacement. Use of damaged power cords could result in fire or electric
shock.

• Be sure to locate the machine as close as possible to a wall outlet. This will allow easy

disconnection of the power cord in the event of an emergency.

• Be sure to push the plug of the power cord fully into the wall outlet. Partially inserted plugs

create an unstable connection that can result in unsafe buildup of heat.

2. Preparing for Printing

Summary of Contents for Ri 100





































































































































































































































































Search results

Summary of Contents for Ri 100

Reviews:

Related manuals for Ri 100

Brands by name

Popular brands

Ricoh Ri 100, Operating Instructions Manual

Search results

Summary of Contents for Ri 100

Reviews:

Related manuals for Ri 100

Brands by name

Popular brands