Ricoh Ri 100 Operating Instructions Manual Download Page 228 | Manualshive

Page: 228 / 260

background image

Message

Causes

Solutions

Cannot use High Temp. /
Power Off On

The temperature is
abnormally high.

Check the installation area and relocate the
machine. Alternatively, wait until the machine
acclimates to the room temperature.
See page 235 "Out of Printable
Temperature Range".

Cannot use Low Temp. /
Power Off On

The temperature is
abnormally low.

Check the installation area and relocate the
machine. Alternatively, wait until the machine
acclimates to the room temperature.
See page 235 "Out of Printable
Temperature Range".

Hardware Problem
Ethernet Board

An error in the Ethernet
port (ethernet board)
network function has
occurred.

Disconnect all cables, turn the machine off,
and then turn it on again. If the message
reappears, contact your sales or service
representative.
See page 236 "Network Interface Error".

Indepdnt.ink set
Indepdnt.ink set / Replace
Ink Crtg
Indepdnt.ink set / Press #
to continue

A non-genuine ink
cartridge was installed.

Use of non-genuine ink cartridges or refilled
ink cartridges may reduce print quality or
cause malfunctions.
See page 248 "Recommended
Consumables".

Ink Collector is not set /
Set the Ink Collector Unit

The ink collector unit is
not installed or is
installed incorrectly.
Alternatively, an ink
collector unit not meant
for this machine may be
installed.

Install the ink collector unit for this machine
correctly. The ink collector unit meant for this
machine is labeled "J089" under its handle.
See page 234 "Ink Collector Unit Not
Detected/Wrong Unit".

Ink Collector Unit is full /
Replace Ink Collector Unit

The ink collector unit is
full.

Replace the ink collector unit.
See page 188 "Replacing an Ink Collector
Unit".

Low Ink

The ink will soon run out.

Make sure you have a new ink cartridge for
the color indicated by the icon.
See page 233 "Cartridge Almost Empty".

9. Troubleshooting

226

«
...
226
227
228
229
230
...
»

Summary of Contents for Ri 100





































































































































































































































































Reviews:

No comments

Related manuals for Ri 100

Brand: Magicard Pages: 30

Brand: Magicard Pages: 35

MAGICARD ID Card Printer

Brand: Magicard Pages: 30

Brand: Magicard Pages: 6

Brand: Oki Pages: 152

Brand: Oki Pages: 140

Brand: Oki Pages: 181

Brand: Oki Pages: 52

Brand: Oki Pages: 229

Brand: Oki Pages: 224

Brand: Oki Pages: 141

Brand: Oki Pages: 160

Brand: Oki Pages: 48

Brand: Oki Pages: 20

Brand: Oki Pages: 52

Brand: Oki Pages: 127

Brand: Oki Pages: 128

Brand: Oki Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands