Ricoh Ri 100 Operating Instructions Manual Download Page 237

Page: 237 / 260

Close the right front cover.

DSA368

If the message reappears, contact your sales or service representative.

Ink Collector Unit Almost Full

The ink collector unit is almost full.
Have a new ink collector unit handy.

• If an ink cartridge starts running out of ink when the ink collector unit is almost full, the alert

indicator will flash and a message informing you of the cartridge's low ink level will appear on the
display.

Ink Collector Unit Full

The ink collector unit is full.
Replace the ink collector unit.
See page 188 "Replacing an Ink Collector Unit".

Used Ink Collector Unit

A used ink collector unit is installed.
Replace the ink collector unit.
See page 188 "Replacing an Ink Collector Unit".

Out of Printable Temperature Range

Printing is not possible because the printer is placed in a location that is too hot or cold.

Status Monitor Errors

235

Summary of Contents for Ri 100





































































































































































































































































Search results

Summary of Contents for Ri 100

Reviews:

Related manuals for Ri 100

Brands by name

Popular brands

Ricoh Ri 100, Operating Instructions Manual

Search results

Summary of Contents for Ri 100

Reviews:

Related manuals for Ri 100

Brands by name

Popular brands