manualshive.com logo in svg

Ricoh LP124w, Software Manual

Share
Download
Ricoh LP124w Software Manual Download Page 286

Monitoring and Configuring the Printer

272

6

SMTPC: username or password wasn’t cor-
rect. 

[

response code

]

 (information)

Connection to the SMTP server failed, because 
the specified SMTP user name is incorrect, or 
the specified SMTP password is incorrect. 
Check the SMTP user name and password.

Snmp over IPv4 is ready

Communication over IPv4 with snmp is 
available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is 
available.

Snmp over IPX is ready.

Communication over IPX with snmp is 
available.

snmpd start.

The snmpd service has started.

started.

The direct print service has started.

Started.

The bonjour function is enabled.

Terminated.

The bonjour function is disabled.

The print server received error <error num-
ber> during attempt to log in to the network. 
Access to the network was denied. Verify that 
the print server name and password are cor-
rect. 

Login to the file server failed. The print server 
is not registered or a password is specified. 
Register the print server without specifying a 
password.

trap account is unavailable.

v3Trap cannot be sent. This could be because 
the Trap destination account is different from 
the account specified by the printer.

usbd is disable.

Plug and Play function and printing is dis-
abled because usbd is disabled in the security 
mode.

Enable usbd in the security mode.

WINS name registration: No response to serv-
er <WINS server address>

There was no response from the WINS server. 
Check the correct WINS server address is en-
tered. Alternatively, check the WINS server is 
functioning properly.

WINS wrong scopeID= <Scope ID>

An invalid scope ID was used. Use a valid 
scope ID.

wpa authentication Failed

WPA authentication failed. Check the WPA 
configuration.

wpa authentication started

WPA authentication has started.

wpa IEEE802.1X started

WPA authentication has started.

wpa connecting to authenticator

WPA is connecting to authenticator.

wpa link up

WPA key exchange has finished, and commu-
nication has been terminated.

wpa probe response doesn’t have IE.

WPA probe response does not have IE.

wpa success authenticated

WPA authentication was successful.

wpa success key received

WPA key reception was successful.

Message

Problem and solutions

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands