Ricoh LP124w Software Manual Download

Page: 242 / 376

Monitoring and Configuring the Printer

228

ifconfig

Use the “ifconfig” command to view and configure TCP/IP (IP address, subnet
mask, broadcast address, default gateway address) for the printer.

❖

View settings

msh> ifconfig

❖

IPv4 Configuration

msh> ifconfig "interface_name" "parameter" "address"

• If you did not enter an interface name, it is automatically set to the Ethernet

interface.

• wlan can be specified only when the IEEE 802.11b interface unit is in-

stalled.

The following explains how to configure an IPv4 address 192.168.15.16 on
Ethernet interface.

msh> ifconfig ether 192.168.15.16

❖

IPv6 Configuration

msh> ifconfig ether inet6 "interface_name" "prefixlen"

The following explains how to configure a IPv6 address to 2001:DB8::100 with
prefix length 64 on the Ethernet interface.

msh> ifconfig ether inet6 2001:DB8::100 64

❖

Netmask configuration

msh> ifconfig "interface_name" netmask "address"

The following explains how to configure a subnet mask 255.255.255.0 on
Ethernet interface.

msh> ifconfig ether netmask 255.255.255.0

❖

Broadcast address configuration

msh> ifconfig "interface_name" broadcast "address"

❖

Changing the Interface

msh> ifconfig "interface" up

You can specify either the Ethernet interface or IEEE 802.11b interface when
using the optional IEEE 802.11b interface unit is installed.

Interface name

Interface configured

ether

Ethernet interface

wlan

IEEE 802.11b Interface

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands