Ricoh LP124w Page 147 Software Manual Download

Page: 147 / 376

System Menu

133

❖

Energy Saver 2

In Energy Saver mode, electric power consumption is reduced.

❖

Energy Saver Timer

Specify the lead time needed to switch to Energy Saver mode.
• 1 minute
• 5 minutes
• 15 minutes
• 30 minutes
• 45 minutes
• 60 minutes

Note

❒

Default: 15 minutes

❖

Memory Usage

Select memory to be used from Font Priority or Frame Priority.
• Font Priority
• Frame Priority

Note

❒

Default : Font Priority

❖

Spool Printing

Specify whether or not to complete spooling before starting to print.
• On
• Off

Note

❒

Default: Off

❒

Spooling stores a sent print job temporarily in the printer, and then prints
it.

❖

Auto Email Notify

Specify whether or not to send an error message to a preset e-mail address
when an error occurs in the printer.
• On
• Off

Important

❒

After changing the setting, turn off the power of the printer briefly, and
then turn it on again.

Note

❒

Default: On

❒

For information, see Web Image Monitor Help.

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands