Ricoh LP124w Software Manual Download

Page: 259 / 376

Remote Maintenance by telnet

245

spoolsw

Use the “spoolsw” command to view and configure Job Spool settings.
You can only specify diprint, lpr, ipp, ftp, smb and sftp protocol.

❖

View settings

The Job Spool setting appears.

msh> spoolsw

❖

Job Spool setting

msh> spoolsw spool {on | off}

Note

❒

Specify “on” to enable Job Spool, or “off” to disable it.

❖

Resetting Job spool setting

msh> spoolsw clear job {on | off}

• When the printer power is cut during job spooling, this determines wheth-

er to reprint the spooled job.

❖

Protocol configuration

msh> spoolsw diprint {on | off}

msh> spoolsw lpr {on | off}

msh> spoolsw ipp {on | off}

msh> spoolsw smb {on | off}

msh> spoolsw ftp {on | off}

msh> spoolsw sftp {on | off}

• You can specify the settings for diprint, lpr, ipp, smb and sftp.

ssdp

Use the “ssdp” command to view and configure SSDP settings.

❖

View settings

msh> ssdp

❖

Setting effective time

msh> ssdp profile {1801-86400}

The default is 10800 seconds.

❖

Advertise packet TTL settings

msh> ssdp ttl {1-255}

The default is 4.

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands