Ricoh LP124w Software Manual Download

Page: 129 / 376

Menu Chart

115

❖

Security Options

Note

❒

[

Service Mode Lock

]

may not appear depending on the setting of the printer.

❒

[

Auto Erase Memory Setting

]

and

[

Erase All Memory

]

appear when the optional

security card is installed.

❖

Host Interface

Note

❒

[

IEEE 802.11b

]

appears when the optional IEEE 802.11b interface unit is in-

stalled.

❖

Language

Menu

Extend Auth. Management

Extended Security

Service Mode Lock

Firmware Version

Network Security Level

Auto Erase Memory Setting

Erase All Memory

Transfer Log Setting

Menu

I/O Buffer

I/O Timeout

Network

IEEE 802.11b

USB Settings

Menu

English

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands