manualshive.com logo in svg

Ricoh LP124w, Software Manual

The Ricoh LP124w Hardware Manual is the essential guide for users of this cutting-edge printer. Accessible, comprehensive, and free to download from our website, this manual provides step-by-step instructions and troubleshooting tips to optimize the performance of your device. Master your printer with ease and enhance your printing experience with the Ricoh LP124w Hardware Manual. Download now at manualshive.com.

Share
Download
background image

Monitoring and Configuring the Printer

254

6

Getting Printer Information over the Network

This section explains details of each item displayed in the printer status and in-
formation.
• UNIX: Use the “lpq” command and “rsh”, “rcp”, “ftp” and “sftp” parameters.
• mshell: Use the “status” command.

Messages

Description

Access Restricted

The job was canceled because user have no au-
thority.

Adjusting...

The printer is initializing or calibrating.

Call Service Center

There is a malfunction in the printer.

Canceled

The job is reset.

Canceling Job...

The job is being reset.

Cannot multi-install: SD Card

SD card you are trying to install has already 
been installed in a different machine.

Card/Counter not inserted

The printer is waiting for prepaid card or key.

Coin or amount not inserted

The printer is waiting for coin to be inserted.

Coin/Key Counter not inserted

The printer is waiting for coin or key counter.

Configuring...

Setting is being changed.

Cooling Down Fusing Unit...

Fusing unit is cooling down.

Cover Open: Finisher

The cover of Finisher is open.

Data Size Error

The data size error occurred.

Empty: Black Toner

The black toner cartridge is almost empty.

Energy Saver Mode

The printer is in Energy Saver Mode.

Error

An error has occurred.

Error: Address Book

An error has occurred in the data of the ad-
dress book.

Error: Command Transmission

An error has occurred in the printer.

Error: DIMM Value

A memory error occurred.

Error: Ethernet Board

An Ethernet board error has occurred.

Error: HDD Board

A hard disk drive board error has occurred.

Error: Memory Switch

A memory error occurred.

Error: Optional Font

An error has occurred in the font file of the 
printer.

Error: PDL

An error has occurred in the page description 
language.

Error: Rem. Certificate Renewal

An error has occurred in the remote certificate 
renewal.

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Related manuals for LP124w

EASYPRINT Compact CM User Documentation preview
Compact CM
Brand: EASYPRINT Pages: 37
Macherey-Nagel NANOCOLOR UV/VIS II User Manual preview
NANOCOLOR UV/VIS II
Brand: Macherey-Nagel Pages: 6
Xerox DocuColor 1632 Printing User Manual preview
DocuColor 1632
Brand: Xerox Pages: 130
Xerox Phaser 6500 Service Manual preview
Phaser 6500
Brand: Xerox Pages: 793
Xerox WorkCentre Pro 32 Specification preview
WorkCentre Pro 32
Brand: Xerox Pages: 14
Aficio dsc424 Operating Instructions Manual preview
dsc424
Brand: Aficio Pages: 156
Konica Minolta bizhub C227 Installation Manual preview
bizhub C227
Brand: Konica Minolta Pages: 12
Output Technology EuroLine Series Operator'S Manual preview
EuroLine Series
Brand: Output Technology Pages: 73
GRAPHTEC SignJet JS310 Series Setup Manual preview
SignJet JS310 Series
Brand: GRAPHTEC Pages: 83
Novexx Solutions LA-BO User Manual preview
LA-BO
Brand: Novexx Solutions Pages: 6
Kyocera Mita 1900N - B/W Laser Printer Operation Manual preview
1900N - B/W Laser Printer
Brand: Kyocera Mita Pages: 286
Kodak ESP Office 6100 Series Extended User Manual preview
ESP Office 6100 Series
Brand: Kodak Pages: 94
Olivetti PR4 SL User Manual preview
PR4 SL
Brand: Olivetti Pages: 8
Xante ColourLaser 21 Series Setup Manual preview
ColourLaser 21 Series
Brand: Xante Pages: 32
Oki MC160MFP Safety And Warranty Manual preview
MC160MFP
Brand: Oki Pages: 56
Xerox DocuPrint 3055 User Manual preview
DocuPrint 3055
Brand: Xerox Pages: 240
Konica Minolta BIZHUB PRO 1050P User Manual preview
BIZHUB PRO 1050P
Brand: Konica Minolta Pages: 588
Durst Automatic Photo Book Station Specifications preview
Automatic Photo Book Station
Brand: Durst Pages: 2

Brands by name

Popular brands

Load more brands