Mazda 2013 CX-5 Workshop Manual Download Page 77

Page: 77 / 223

DTC U0452:86 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2893000.html[1/7/13 9:30:44 AM]

(See

STEP DEPLOYMENT CONTROL
SYSTEM]

Are any DTCs detected?

VERIFY THAT THE SAME DTC IS NOT

PRESENT

Clear the DTCs from the

memory.

(See

ON-BOARD DIAGNOSIS

[DYNAMIC STABILITY CONTROL
(DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the SAS control

module, then go to the next step.

(See

SAS CONTROL MODULE

REMOVAL/INSTALLATION [STANDARD DEPLOYMENT
CONTROL SYSTEM]

(See

SAS CONTROL MODULE

REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT
CONTROL SYSTEM]

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE

PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY

CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands