Mazda 2013 CX-5 Workshop Manual Download Page 120

Page: 120 / 223

NO.8 HILL LAUNCH ASSIST (HLA) OPERATES EVEN ON A DOWNHILL/HILL LAUNCH ASSIST (HLA) DOES NOT OPERATE ON A SLOPE [DYNAM...

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2896300.html[1/7/13 9:32:07 AM]

Communication error between DSC HU/CM and PCM

Communication error between DSC HU/CM and instrument cluster

Brake (foot brake/parking brake) drag

Diagnostic procedure

STEP

INSPECTION

ACTION

VERIFY DTC FOR RELATED MODULES

Retrieve the DSC HU/CM, PCM, TCM

(ATX) and instrument cluster DTC using

the M-MDS.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

(See

ON-BOARD DIAGNOSTIC TEST

[SKYACTIV-G 2.0]

(See

ON-BOARD DIAGNOSTIC SYSTEM DTC

INSPECTION [FW6A-EL, FW6AX-EL]

(See

DTC INSPECTION [INSTRUMENT

CLUSTER]

Are any DTCs present?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

(See

DTC TABLE [SKYACTIV-G 2.0]

(See

ON-BOARD DIAGNOSTIC SYSTEM

DTC TABLE [FW6A-EL, FW6AX-EL]

(See

DTC TABLE [INSTRUMENT

CLUSTER]

No Go to the next step.

VERIFY IF FALSE DETECTION OF INCLINATION

ANGLE CAUSED BY MALFUNCTIONING SAS CONTROL

MODULE INSTALLATION

Inspect the SAS control module

installation condition for the following:

Is the module installed

with any twisting?

Is the module installed

correctly?

YesGo to the next step.

No Repair the SAS control module

installation condition.

(See

SAS CONTROL MODULE

REMOVAL/INSTALLATION [TWO-STEP
DEPLOYMENT CONTROL SYSTEM]

(See

SAS CONTROL MODULE

REMOVAL/INSTALLATION [STANDARD
DEPLOYMENT CONTROL SYSTEM]

VERIFY IF MALFUNCTION CAUSED BY

INITIALIZATION PROCEDURE FOR LOW-G SENSOR

NOT PERFORMED

Verify if malfunction caused by

initialization procedure for low-G sensor

not performed.

Has the initialization for the low-G sensor

been performed after replacing the DSC

HU/CM and the SAS control module?

YesGo to the next step.

No Perform the initialization procedure.

(See

DSC RELATED PARTS SENSOR

INITIALIZATION PROCEDURE

VERIFY IF MALFUNCTION CAUSED BY TIRE

MALFUNCTION PERFORMED

YesGo to the next step.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands