Mazda 2013 CX-5 Workshop Manual Download Page 79

Page: 79 / 223

DTC U2101:00/U2300:52/U2300:54/U2300:55/U2300:56/U2300:64 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2905800.html[1/7/13 9:30:49 AM]

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, go to the

next step.

No Go to Step 6.

VERIFY IF PARTS FROM ANOTHER VEHICLE

INSTALLED TO INSTRUMENT CLUSTER, PCM OR DSC

HU/CM

Verify if an instrument cluster, PCM or DSC

HU/CM from another vehicle is installed.

Has an instrument cluster, PCM, DSC

HU/CM or other vehicle part been installed

to vehicle?

YesInstall the correct instrument cluster,

PCM or DSC HU/CM, then go to Step

(See

INSTRUMENT CLUSTER

REMOVAL/INSTALLATION

(See

PCM REMOVAL/INSTALLATION

[SKYACTIV-G 2.0]

(See

DSC HU/CM

REMOVAL/INSTALLATION

No Go to the next step.

INSPECT FOR INSTRUMENT CLUSTER/PCM

MALFUNCTION

Switch the ignition to off.

Using the M-MDS, perform the DTC

inspection for the instrument cluster and

PCM.

(See

DTC INSPECTION [INSTRUMENT

CLUSTER]

(See

ON-BOARD DIAGNOSTIC TEST

[SKYACTIV-G 2.0]

Are any DTCs detected?

YesGo to applicable DTC inspection.

(See

DTC TABLE [INSTRUMENT

CLUSTER]

(See

DTC TABLE [SKYACTIV-G 2.0]

No Go to the next step.

VERIFY THAT THE SAME DTC IS NOT PRESENT

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands