Mazda 2013 CX-5 Workshop Manual Download Page 84

Page: 84 / 223

DTC U3003:08/U3003:16/U3003:17 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2902000.html[1/7/13 9:30:55 AM]

INSPECT BATTERY GRAVITY

Is battery specific gravity as specified?

YesGo to the next step.

No Replace the battery, then go to

Step 7.

(See

BATTERY

REMOVAL/INSTALLATION
[SKYACTIV-G 2.0]

INSPECT CHARGING SYSTEM

Are the generator and the drive belt tensions

normal?

YesGo to the next step.

No Replace the generator and/or drive

belt if necessary.

(See

GENERATOR

REMOVAL/INSTALLATION
[SKYACTIV-G 2.0]

(See

DRIVE BELT

REMOVAL/INSTALLATION
[SKYACTIV-G 2.0]

Go to Step 7.

INSPECT FUSE CONDITION

Inspect the following fuses.

SRS1 7.5A

ABS/DSC S 30A

ABS/DSC M 50A

Is the fuse normal?

YesGo to the next step.

No Replace the fuse, then go to Step

INSPECT DSC HU/CM POWER SUPPLY FOR OPEN

CIRCUIT

Disconnect the DSC HU/CM connectors.

Switch the ignition ON (engine off).

Measure the voltage between following

connector terminals of the DSC HU/CM

(vehicle harness-side) and body ground:

DSC HU/CM: A—Body

ground

DSC HU/CM: B—Body

ground

DSC HU/CM: Q—Body

ground

Is the voltage

10 V or more

YesGo to the next step.

No Repair or replace the wiring

harness, then go to Step 7.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands