Mazda 2013 CX-5 Workshop Manual Download Page 197

Page: 197 / 223

DSC HU/CM REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041500801000.html[1/7/13 9:36:09 AM]

c. Switch the ignition ON (engine off) and wait for

3 s or more

d. The automatic configuration procedure is completed.

7. Perform the DSC related parts sensor initialization procedure. (See

DSC RELATED PARTS SENSOR

INITIALIZATION PROCEDURE

8. Perform the tire pressure monitoring system initialization procedure. (See

TIRE PRESSURE MONITORING

SYSTEM INITIALIZATION PROCEDURE

9. Clear the DTCs from the memory. (See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

1DSC HU/CM connector

(See

DSC HU/CM Connector Removal Note

(See

DSC HU/CM Connector Installation Note

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands