Mazda 2013 CX-5 Workshop Manual Download Page 57

Page: 57 / 223

DTC C1031:41 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2906700.html[1/7/13 9:30:00 AM]

VERIFY THAT THE SAME DTC IS NOT PRESENT

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the

DSC HU/CM, then go to the next step.

(See

DSC HU/CM

REMOVAL/INSTALLATION

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands