Mazda 2013 CX-5 Workshop Manual Download Page 22

Page: 22 / 223

DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2878200.html[1/7/13 9:28:47 AM]

CONTROL (DSC)]

Does the solenoid valve operate?

VERIFY DTC TROUBLESHOOTING COMPLETED

Clear the DTC from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY

CONTROL (DSC)]

Start the engine and drive the vehicle at

10 km/h

{6.2 mph} or more

Gradually slow down and stop vehicle.

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the DSC HU/CM, then go

to the next step.

(See

DSC HU/CM REMOVAL/INSTALLATION

No Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

Are any other DTCs present?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL

(DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands