Mazda 2013 CX-5 Workshop Manual Download Page 140

Page: 140 / 223

BRAKE SWITCH INSPECTION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100801900.html[1/7/13 9:33:02 AM]

< Previous

Next >

2013 - CX-5 - Brakes

BRAKE SWITCH INSPECTION

CAUTION:

Inspect the brake switch with it installed to the brake pedal, otherwise the brake switch

may not operate normally. If the brake switch is removed from the brake pedal, replace

the brake switch with a new one.

1. Remove the lower panel. (See

LOWER PANEL REMOVAL/INSTALLATION

2. Remove the front heat duct (LH). (See

FRONT HEAT DUCT REMOVAL/INSTALLATION

3. Disconnect the brake switch connector.

4. Verify that the continuity is as indicated in the table.

If not as indicated in the table, replace the brake switch. (See

BRAKE PEDAL

REMOVAL/INSTALLATION

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands