Mazda 2013 CX-5 Workshop Manual Download Page 52

Page: 52 / 223

DTC C0089:64 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2906500.html[1/7/13 9:29:51 AM]

Diagnostic procedure

STEP

INSPECTION

ACTION

INSPECT FOR INSTRUMENT CLUSTER MALFUNCTION

Switch the ignition to off.

Using the M-MDS, perform the DTC inspection for the

instrument cluster.

(See

DTC INSPECTION [INSTRUMENT CLUSTER]

Are any DTCs detected?

YesGo to applicable DTC

inspection.

(See

DTC TABLE

[INSTRUMENT CLUSTER]

No Go to the next step.

INSPECT TCS OFF SWITCH SIGNAL CIRCUIT FOR SHORT TO GROUND

YesRepair or replace the

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands