Mazda 2013 CX-5 Workshop Manual Download Page 115

Page: 115 / 223

NO.5 ABS OR TCS*1 OPERATES FREQUENTLY/TCS DOES NOT WORK CORRECTLY *1: DSC SYSTEM FUNCTION CONTAINS TRACTION CONTR...

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2896000.html[1/7/13 9:31:52 AM]

PULSE

Perform the Voltage Pattern

Inspection for each ABS wheel-

speed sensor.

(See

FRONT ABS WHEEL-SPEED

SENSOR INSPECTION

(See

REAR ABS WHEEL-SPEED

SENSOR INSPECTION [2WD]

(See

REAR ABS WHEEL-SPEED

SENSOR INSPECTION [AWD]

Is the output voltage pattern

normal?

YesFound malfunctioning part according to the

“INTERMITTENT CONCERN

TROUBLESHOOTING”.

(See

PRECAUTION [DYNAMIC STABILITY

CONTROL (DSC)]

No ABS wheel-speed sensor installation

inspection:

Inspect the ABS wheel-speed

sensor for looseness and

confirm it is securely adhered.

ABS sensor rotor installation inspection:

Inspect the ABS sensor rotor

for poor installation.

Repair or replace any malfunctioning parts

according to the inspection result.

When performing an asterisked (*) troubleshooting inspection, shake the wiring harness

and connectors while doing the inspection to discover whether poor contact points are the

cause of any intermittent malfunctions. If there is a problem, check to make sure

connectors, terminals and wiring harness are connected correctly and undamaged.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands