Mazda 2013 CX-5 Workshop Manual Download Page 105

Page: 105 / 223

NO.2 ANY OF THE FOLLOWING LIGHTS STAY ON: (ABS WARNING LIGHT, TCS/DSC INDICATOR LIGHT AND/OR TCS OFF INDICATOR LIGHT) [...

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2895700.html[1/7/13 9:31:38 AM]

terminal AL (wiring harness-side) and body

ground.

Is there continuity?

harness for a possible open

circuit and poor contact in

ground point.

CONFIRM PCM DTCs

Retrieve the PCM DTCs using the M-MDS (IDS).

(See

ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G

2.0]

Are any DTCs present?

YesGo to the applicable DTC

inspection.

(See

DTC TABLE [SKYACTIV-G

2.0]

No Go to the next step.

VERIFY IF MALFUNCTION CAUSED BY INITIALIZATION

PROCEDURE FOR MODULE NOT PERFORMED

Verify if malfunction caused by initialization

procedure for brake fluid pressure sensor not

performed.

Has the initial setting for the brake fluid

pressure sensor been performed after replacing

the DSC HU/CM?

YesGo to the next step.

No Perform the brake fluid pressure

sensor initial setting.

(See

DSC RELATED PARTS

SENSOR INITIALIZATION
PROCEDURE

VERIFY IF MALFUNCTION CAUSED BY INITIALIZATION

PROCEDURE FOR LOW-G SENSOR NOT PERFORMED

Verify if malfunction caused by initialization

procedure for low-G sensor not performed.

Has the initial setting for the low-G sensor been

performed after replacing the DSC HU/CM and

the SAS control module?

YesGo to the next step.

No Perform the low-G sensor initial

setting.

(See

DSC RELATED PARTS

SENSOR INITIALIZATION
PROCEDURE

VERIFY IF MALFUNCTION CAUSED BY INITIALIZATION

PROCEDURE FOR YAW RATE SENSOR NOT PERFORMED

Verify if malfunction caused by initialization

procedure for yaw rate sensor not performed.

Has the initial setting for the yaw rate sensor

been performed after replacing the DSC HU/CM

and the SAS control module?

YesGo to the next step.

No Perform the yaw rate sensor

initial setting.

(See

DSC RELATED PARTS

SENSOR INITIALIZATION
PROCEDURE

VERIFY WHETHER MALFUNCTION IS IN INSTRUMENT

CLUSTER OR DSC HU/CM

Connect the M-MDS (IDS) to the DLC-2.

Turn off and on all warning light and indicator

lights using the instrument cluster PID WL+IL of

active command modes.

(See

ACTIVE COMMAND MODES INSPECTION

[INSTRUMENT CLUSTER]

Do the ABS warning light, brake system warning

light, TCS/DSC indicator light and DSC OFF

YesReplace the DSC HU/CM.

(Internal malfunction)

(See

DSC HU/CM

REMOVAL/INSTALLATION

No Replace the instrument cluster.

(See

INSTRUMENT CLUSTER

REMOVAL/INSTALLATION

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands