Mazda 2013 CX-5 Workshop Manual Download Page 118

Page: 118 / 223

NO.7 TCS/DSC INDICATOR LIGHT FLASHES (WHEN NEITHER THE TCS NOR THE DSC ARE OPERATING) [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2896200.html[1/7/13 9:32:02 AM]

< Previous

Next >

2013 - CX-5 - Brakes

NO.7 TCS/DSC INDICATOR LIGHT FLASHES (WHEN NEITHER THE TCS NOR THE DSC ARE

OPERATING) [DYNAMIC STABILITY CONTROL (DSC)]

TCS/DSC indicator light flashes (when neither the TCS nor the DSC are operating)

POSSIBLE

CAUSE

Non-completion of DSC related parts sensor initialization. (If the initialization is

not carried out after replacing the DSC HU/CM and/or SAS control module, a

TCS/DSC indicator light will flash. In this case, the DSC is not detected.)

Diagnostic procedure

STEP

INSPECTION

ACTION

INSPECT CONNECTION OF DSC HU/CM AND SAS

CONTROL MODULE CONNECTORS

Inspect for connection of DSC HU/CM and

SAS control module (yaw rate sensor, low-

G sensor) connectors.

Are DSC HU/CM and SAS control module

connectors connected securely?

YesPerform the initialization procedure.

(See

DSC RELATED PARTS SENSOR

INITIALIZATION PROCEDURE

No Perform the initialization procedure

after connect the suspected connector

securely.

(See

DSC RELATED PARTS SENSOR

INITIALIZATION PROCEDURE

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands