Mazda 2013 CX-5 Workshop Manual Download Page 59

Page: 59 / 223

DTC C1031:54 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2906900.html[1/7/13 9:30:05 AM]

(See

Is the pressure as specified?

then go to the next step.

(See

WHEEL AND TIRE SPECIFICATION

INITIALIZE THE TPMS

Initialize the TPMS.

(See

TIRE PRESSURE MONITORING

SYSTEM INITIALIZATION PROCEDURE

Is the initialization normally completed?

YesGo to the next step.

No Repeat the inspection from Step 1.

If the malfunction recurs, replace the

DSC HU/CM, then go to the next step.

(See

DSC HU/CM

REMOVAL/INSTALLATION

VERIFY THAT THE SAME DTC IS NOT PRESENT

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the

DSC HU/CM, then go to the next step.

(See

DSC HU/CM

REMOVAL/INSTALLATION

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands