Mazda 2013 CX-5 Workshop Manual Download Page 55

Page: 55 / 223

DTC C1031:35 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2906600.html[1/7/13 9:29:56 AM]

Is the TPMS set switch normal?

SWITCH REMOVAL/INSTALLATION

VERIFY THAT THE SAME DTC IS NOT PRESENT

Reconnect all disconnected

connectors.

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS

[DYNAMIC STABILITY CONTROL
(DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands