Mazda 2013 CX-5 Workshop Manual Download Page 69

Page: 69 / 223

DTC U0401:00 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2887900.html[1/7/13 9:30:26 AM]

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

If the malfunction recurs, replace the PCM,

then go to the next step.

(See

PCM REMOVAL/INSTALLATION

[SKYACTIV-G 2.0]

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands