Mazda 2013 CX-5 Workshop Manual Download Page 16

Page: 16 / 223

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2800200.html[1/7/13 9:28:37 AM]

Shift/selector lever at R position: ON

Inspect the TCM. (ATX)

(See

ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL, FW6AX-EL]

STR_ANG_C

(Calculated Value)

Steering wheel in neutral position (not turned):

0°

Steering wheel turned to left: Changes

0°—positive

Steering wheel turned to right: Changes

0°—negative

Inspect the EPS CM.

(See

EPS CONTROL MODULE INSPECTION

STR_ANG_R

(Raw Value)

TPMS_TYPE

No_DDS/DDS+TOM_EU/DDS+TOM_US

TPMS not equipped: No_DDS

TPMS equipped (Corresponding to European regulations): DDS+TOM_EU

TPMS equipped (Corresponding to U.S. regulations): DDS+TOM_US

Perform the DTC inspection for the DSC HU/CM.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

V_INLET_LF

Off/On

Solenoid valve not activated: Off

Solenoid valve activated: On

Inspect the DSC HU/CM.

(See

DSC HU/CM INSPECTION

V_INLET_LR

V_INLET_RF

V_INLET_RR

V_OUTLET_LF

V_OUTLET_LR

V_OUTLET_RF

V_OUTLET_RR

V_STB_LF/RR

Off/On

Solenoid valve activated: On

Solenoid valve not activated: Off

Inspect the DSC HU/CM.

(See

DSC HU/CM INSPECTION

V_STB_RF/LR

V_TRC_LF/RR

Off/On

Solenoid valve activated: On

Solenoid valve not activated: Off

Inspect the DSC HU/CM.

(See

DSC HU/CM INSPECTION

V_TRC_RF/LR

VPWR_B_SOL

Ignition switched ON (engine off):

Approx. 12.2 V

Idling:

Approx. 14.1 V

Inspect power supply circuit.

(See

DSC HU/CM INSPECTION

VSPD

KPH, MPH

Vehicle stopped:

0 KPH, 0 MPH

Vehicle running: Vehicle speed

Inspect the DSC HU/CM.

(See

DSC HU/CM INSPECTION

WSPD_SEN_LF

KPH, MPH

Vehicle stopped:

0 KPH, 0 MPH

Vehicle running: Vehicle speed

Inspect the front ABS wheel-speed sensor.

(See

FRONT ABS WHEEL-SPEED SENSOR INSPECTION

WSPD_SEN_LR

Inspect the rear ABS wheel-speed sensor.

(See

REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD]

(See

REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD]

WSPD_SEN_RF

Inspect the front ABS wheel-speed sensor.

(See

FRONT ABS WHEEL-SPEED SENSOR INSPECTION

WSPD_SEN_RR

Inspect the rear ABS wheel-speed sensor.

(See

REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD]

(See

REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD]

YAW_RATE_C

(Calculated Value)

°/s

Vehicle stopped or driving straight:

0 °/s

Cornering to left: Changes

0 °/s—positive

Cornering to right: Changes

0 °/s—negative

Perform the DTC inspection for the SAS control module.

(See

DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM]

(See

DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]

YAW_RATE_R

(Raw Value)

After ignition is switched off, switch it ON (engine off or on) and verify.

Snapshot Data Table

NOTE:

Refer to PID monitor table for confirm the DSC system operation status while the DSC CM does not store the DTC. (See

PID/DATA Monitor Table

Snapshot data items are not displayed, according to detected DTC.

Snapshot data item

Unit

Definition

Corresponding data monitor items

AAT

°C, °F

Ambient air temperature

—

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands