Mazda 2013 CX-5 Workshop Manual Download Page 137

Page: 137 / 223

BRAKE PEDAL REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100801200.html[1/7/13 9:32:56 AM]

< Previous

Next >

2013 - CX-5 - Brakes

BRAKE PEDAL REMOVAL/INSTALLATION

CAUTION:

The clearance between the brake switch and the brake pedal is automatically adjusted to the

correct amount when the brake switch is inserted into the installation hole on the brake pedal and

rotated to fix in place. If the brake switch is not properly installed, the clearance may be incorrect,

causing a brake light malfunction. Therefore, always verify that the brake pedal is properly installed

and fully released before installing the brake switch to the pedal.

Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again.

Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or

performing any procedure that changes the pedal stroke.

1. Remove the battery. (See

BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0]

2. Disconnect the brake pipes from the master cylinder. (See

MASTER CYLINDER

REMOVAL/INSTALLATION

3. Disconnect the clutch reserve hose from the master cylinder. (MTX) (See

MASTER CYLINDER

REMOVAL/INSTALLATION

4. Remove the side wall (driver side). (See

SIDE WALL REMOVAL/INSTALLATION

5. Remove the front heat duct (LH). (See

FRONT HEAT DUCT REMOVAL/INSTALLATION

6. Remove in the order indicated in the table.

7. Install in the reverse order of removal.

8. After installation, add brake fluid, bleed the air, and inspect for fluid leakage. (See

BRAKE FLUID AIR

BLEEDING

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands