Mazda 2013 CX-5 Workshop Manual Download Page 31

Page: 31 / 223

DTC C0031:11/C0031:15/C0034:11/C0034:15/C0037:11/C0037:15/C003A:11/C003A:15 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2180700.html[1/7/13 9:29:08 AM]

Diagnostic procedure

STEP

INSPECTION

ACTION

INSPECT ABS WHEEL-SPEED SENSOR FOR SHORT TO GROUND

Switch the ignition to off.

Disconnect the DSC HU/CM connectors.

Inspect for continuity between the following DSC HU/CM connector terminals

(vehicle harness-side) and body ground:

RF ABS wheel-speed sensor (+): F

RF ABS wheel-speed sensor (-): C

LF ABS wheel-speed sensor (+): AG

LF ABS wheel-speed sensor (-): AJ

RR ABS wheel-speed sensor (+): AA

RR ABS wheel-speed sensor (-): X

LR ABS wheel-speed sensor (+): L

YesGo to the next step.

No Go to Step 3.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands