Mazda 2013 CX-5 Workshop Manual Download Page 153

Page: 153 / 223

VACUUM PUMP REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100803600.html[1/7/13 9:33:42 AM]

(See

Vacuum Pump Removal Note

(See

Vacuum Pump and O-ring Installation Note

5O-ring

(See

Vacuum Pump and O-ring Installation Note

Vacuum Pump Removal Note

1. When removing the vacuum pump, place a rag under the installation surface of the vacuum pump so that engine

oil does not get on other parts.

2. Remove the vacuum pump.

Vacuum Pump and O-ring Installation Note

1. Rotate the vacuum pump by hand to drain the remainder of the engine oil in the vacuum pump.

2. Degrease the O-ring installation groove and installation surface.

3. Install the new O-ring to the vacuum pump.

4. Install the vacuum pump.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands