Mazda 2013 CX-5 Workshop Manual Download Page 61

Page: 61 / 223

DTC C1031:68 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2907000.html[1/7/13 9:30:10 AM]

(See

SENSOR INSPECTION [FULL-AUTO
AIR CONDITIONER]

Is the ambient temperature

sensor normal?

(See

AMBIENT TEMPERATURE SENSOR

REMOVAL/INSTALLATION [FULL-AUTO AIR
CONDITIONER]

VERIFY THAT THE SAME DTC IS NOT PRESENT

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS

[DYNAMIC STABILITY CONTROL
(DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the PCM,

then go to the next step.

(See

PCM REMOVAL/INSTALLATION [SKYACTIV-

G 2.0]

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands