Mazda 2013 CX-5 Workshop Manual Download Page 122

Page: 122 / 223

NO.8 HILL LAUNCH ASSIST (HLA) OPERATES EVEN ON A DOWNHILL/HILL LAUNCH ASSIST (HLA) DOES NOT OPERATE ON A SLOPE [DYNAM...

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2896300.html[1/7/13 9:32:07 AM]

PCM

RPM (Engine speed

signal)

APP (APP sensor signal)

CPP (Clutch pedal signal:

MTX)

M_GEAR (Manual gear

position signal: MTX)

GEAR (Gear commanded

signal: ATX)

TCM (ATX)

TR (Transaxle range

sensor signal)

INSTRUMENT CLUSTER

P_BRAKE_SW (Parking

brake signal)

Are all PID values normal?

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands