Mazda 2013 CX-5 Workshop Manual Download Page 108

Page: 108 / 223

NO.3 BRAKE SYSTEM WARNING LIGHT STAY ON [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2895800.html[1/7/13 9:31:43 AM]

Is the brake fluid amount normal?

Is the parking brake lever released?

If the brake fluid refilled:

Inspect and repair the

brake line for leakage.

CONFIRM DSC HU/CM DTC

Retrieve the DSC HU/CM DTC using

the M-MDS (IDS).

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are any DTCs present?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No If communication error message is

displayed on the M-MDS (IDS) screen:

Go to the next step.

If communication error message is not

displayed:

Go to Step 4.

INSPECT CONNECTION OF DSC HU/CM

CONNECTOR

Inspect for connection of the DSC

HU/CM connector.

Is the DSC HU/CM connector

connected securely?

YesGo to the next step.

No Connect the DSC HU/CM connector

securely, then go to the next step.

CONFIRM INSTRUMENT CLUSTER OPERATION

RECORD

Retrieve the warning system operation

history using the M-MDS (IDS).

(See

INSTRUMENT CLUSTER OPERATION

RECORD

Is the brake system warning light

illumination history recorded?

YesIf the Brake Waning Lamp recorded:

Go to Step 5.

If the Brake Waning Lamp (Brake fluid

low) recorded:

Go to Step 6.

If the Brake Waning Lamp (Parking Brake

ON over 20 km/h or 12.4 mile/h)

recorded:

Go to Step 8.

No Go to Step 10.

VERIFY WHETHER MALFUNCTION IS IN

INSTRUMENT CLUSTER OR ELSEWHERE

Connect the M-MDS (IDS) to the DLC-

Turn off and on all warning light and

indicator lights using the instrument

cluster PID WL+IL of active command

modes.

(See

ACTIVE COMMAND MODES

YesGo to Step 10.

No Replace the instrument cluster.

(See

INSTRUMENT CLUSTER

REMOVAL/INSTALLATION

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands