Mazda 2013 CX-5 Workshop Manual Download Page 145

Page: 145 / 223

POWER BRAKE UNIT INSPECTION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100801700.html[1/7/13 9:33:23 AM]

Using SST

NOTE:

When performing the inspection using the

SST

, inspect the brake pipe on the left or right

front wheel.

The following procedure and figures show the inspection for the brake pipe on the left front

wheel.

Pre-inspection preparation

1. Remove the clips.

2. Set the splash shield out of the way.

3. Disconnect the brake pipe from the brake hose.

4. Remove the clip.

5. Remove the brake hose from the bracket.

6. Detach the brake pipe from the pipe holder.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands