Mazda 2013 CX-5 Workshop Manual Download Page 176

Page: 176 / 223

CALIPER (REAR) DISASSEMBLY/ASSEMBLY

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100800600.html[1/7/13 9:34:55 AM]

4Dust seal

(See

Dust Seal, Piston Assembly Note

5Piston seal

6Caliper body

2. Assemble in the reverse order of removal.

Piston Disassembly Note

1. Rotate the piston counter-clockwise using the

SST

, remove the piston from the caliper body.

Dust Seal, Piston Assembly Note

1. Assemble the dust seal to the piston.

2. Assemble the lip of the dust seal to the groove of the caliper body with the dust seal is

assembled to the piston as shown in the figure.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands