Mazda 2013 CX-5 Workshop Manual Download Page 121

Page: 121 / 223

NO.8 HILL LAUNCH ASSIST (HLA) OPERATES EVEN ON A DOWNHILL/HILL LAUNCH ASSIST (HLA) DOES NOT OPERATE ON A SLOPE [DYNAM...

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0403b2896300.html[1/7/13 9:32:07 AM]

Inspect the tire pressure and condition.

Are tire pressure and condition normal?

No If the pressure is incorrect, adjust the

tire pressure to the specification.

If the tires are worn, replace the tires.

INSPECT RELATED MODULES FOR MALFUNCTION

CAUSED BY FALSE SIGNAL

Access the following DSC HU/CM, PCM

and instrument cluster PIDs using the M-

MDS:

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

(See

PCM INSPECTION [SKYACTIV-G 2.0]

(See

ON-BOARD DIAGNOSTIC SYSTEM

PID/DATA MONITOR INSPECTION [FW6A-
EL, FW6AX-EL]

(See

PID/DATA MONITOR INSPECTION

[INSTRUMENT CLUSTER]

DSC HU/CM

BRAKE_SW (Brake

signal)

LON_ACCL_C (Low-G

sensor (longitudinal G)

calculated value signal)

LON_ACCL_R (Low-G

sensor (longitudinal G)

raw value signal)

BRK_F_P_C (Brake fluid

pressure calculated value

signal)

BRK_F_P_R (Brake fluid

pressure raw value

signal)

WSPD_LF (ABS wheel-

speed sensor (LF) signal)

WSPD_RF (ABS wheel-

speed sensor (RF)

signal)

WSPD_LR (ABS wheel-

speed sensor (LR)

signal)

WSPD_RR (ABS wheel-

speed sensor (RR)

signal)

YesInspect the following:

Brake (foot

brake/parking brake)

drag

Engine output

malfunction

Repair or replace any malfunctioning

parts according to the inspection result.

No Inspect the related parts and wiring

harness.

Repair or replace any malfunctioning

parts according to the inspection result.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands