Mazda 2013 CX-5 Workshop Manual Download Page 214

Page: 214 / 223

REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0415008002a1.html[1/7/13 9:36:49 AM]

Sensor Output Value Inspection

1. Switch the ignition to off.

2. Connect the M-MDS to the DLC-2.

3. Select the following PIDs using the M-MDS:

WSPD_SEN_LR (LR ABS wheel-speed sensor)

WSPD_SEN_RR (RR ABS wheel-speed sensor)

4. Start the engine and drive the vehicle.

5. Verify that the display of the M-MDS shows the same value as the speedometer.

If there is any malfunction, replace the ABS wheel-speed sensor.

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands