Mazda 2013 CX-5 Workshop Manual Download Page 211

Page: 211 / 223

REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041500800100.html[1/7/13 9:36:44 AM]

< Previous

Next >

2013 - CX-5 - Brakes

REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION

1. Remove the trunk board. (See

TRUNK BOARD REMOVAL/INSTALLATION

2. Remove the trunk end trim. (See

TRUNK END TRIM REMOVAL/INSTALLATION

3. Remove the rear scuff plate. (See

REAR SCUFF PLATE REMOVAL/INSTALLATION

4. Remove the trunk side trim. (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

5. Disconnect the rear ABS wheel-speed sensor connector.

6. Press the rear ABS wheel-speed sensor tabs and press out the sensor toward the outside of the vehicle.

7. Remove in the order indicated in the table.

8. Install in the reverse order of removal.

9. After installation, verify that there is no twisting in the rear ABS wheel-speed sensor.

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands