Mazda 2013 CX-5 Workshop Manual Download Page 15

Page: 15 / 223

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2800200.html[1/7/13 9:28:37 AM]

U2300:54

Control disabled

Control enabled

Control disabled

U2300:55

U2300:56

U2300:64

U3000:49 Control disabled

Control disabled

U3003:08

Control enabled

U3003:16 Control disabled

Control enabled

Control disabled

*6*7

U3003:17 Control disabled

Control disabled

Control disabled when two wheels or more have a malfunction.

Enabled depending on malfunction content.

AWD only

ATX only

When power supply voltage is 7.9—9.6 V for 550 ms or more.

When power supply voltage is 6.0—7.9 V for 630 ms or more.

When power supply voltage is below 6 V for 50 ms or more.

PID/DATA Monitor Table

PID name (definition)

Unit/Condition

Operation condition (reference)

Action

BRAKE_SW

Off/On

Brake pedal released: Off

Brake pedal depressed: On

Inspect the brake switch.

(See

BRAKE SWITCH INSPECTION

BRK_F_P_C

(Calculated Value)

Pa, psi

Brake pedal depressed: Changes according to the brake fluid pressure

Inspect the brake fluid pressure sensor.

(See

BRAKE FLUID PRESSURE SENSOR INSPECTION

BRK_F_P_R

(Raw Value)

DDS_MODE

Not_Learned/Learning/Learned

During initialization: Not_Learned

During learning: Learning

Learning completed

: Learned

Perform the DTC inspection for the DSC HU/CM.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

DSC_OFF_SW

Off/On

TCS OFF switch is released: Off

TCS OFF switch is depressed: On

Inspect the TCS OFF switch.

(See

TCS OFF SWITCH INSPECTION

DSC_ST

Off/On

During TCS OFF mode: Off

Other than TCS OFF mode: On

Perform the DTC inspection for the DSC HU/CM.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

LAT_ACCL_C

(Calculated Value)

Vehicle stopped or driving at constant speed:

0 G

Cornering to left: Changes

0 G—positive

Cornering to right: Changes

0 G—negative

Perform the DTC inspection for the SAS control module.

(See

DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM]

(See

DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]

LAT_ACCL_R

(Raw Value)

LON_ACCL_C

(Calculated Value)

Vehicle stopped or driving at constant speed:

0 G

Vehicle is driving at a acceleration: Changes

0 G—positive

Vehicle is driving at a deceleration: Changes

0 G—negative

Perform the DTC inspection for the SAS control module.

(See

DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM]

(See

DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]

LON_ACCL_R

(Raw Value)

P_BRAKE_SW

Off/On

Parking brake lever released: OFF

Parking brake lever pulled: ON

Inspect the parking brake switch.

(See

PARKING BRAKE SWITCH INSPECTION

PMP_MT

Off/On

Pump motor not activated: Off

Pump motor activated: On

Inspect the DSC HU/CM.

(See

DSC HU/CM INSPECTION

PMP_MT_SP

R_GEAR_SW

Off/On

Except shift/selector lever at R position: OFF

Inspect the PCM. (MTX)

(See

PCM INSPECTION [SKYACTIV-G 2.0]

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands