Mazda 2013 CX-5 Workshop Manual Download Page 124

Page: 124 / 223

GENERAL PROCEDURES (BRAKE)

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041000800100.html[1/7/13 9:32:13 AM]

connectors. (See

NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0]

DSC Related Parts

1. Make sure that there are no DTCs in the DSC memory after working on DSC related parts. If

there are any DTCs in the memory, clear them. (See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

DSC Related Part Sensor Initialization Procedure

WARNING:

If the initialization procedure is not completed, the DSC will not operate properly and it

might cause an unexpected accident. Therefore, when replacing or removing the following

parts, make sure to perform the initialization procedure to insure proper DSC operation.

1. When replacing or removing the following parts, perform the initialization procedure. (See

DSC HU/CM

Tire Pressure Monitoring System Initialization Procedure

CAUTION:

If the tire pressure monitoring system initialization procedure is performed with the tire

pressures not to specification, the system may not operate normally. Therefore, always

inspect and adjust the tire pressure of all 4 tires before performing the tire pressure

monitoring system initialization procedure.

NOTE:

Perform the tire pressure monitoring system initialization when the following operations

have been performed: (See

TIRE PRESSURE MONITORING SYSTEM INITIALIZATION

PROCEDURE

Tire pressures have been adjusted

Tires or wheels have been replaced

Tires have been rotated

DSC HU/CM replaced

DSC HU/CM connector disconnected

Battery replaced

Negative battery cable is disconnected

1. Perform the tire pressure monitoring system initialization procedure when the tire pressure

monitoring system warning light illuminates. (See

TIRE PRESSURE MONITORING SYSTEM

INITIALIZATION PROCEDURE

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands