Mazda 2013 CX-5 Workshop Manual Download Page 54

Page: 54 / 223

DTC C1031:35 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2906600.html[1/7/13 9:29:56 AM]

< Previous

Next >

2013 - CX-5 - Brakes

DTC C1031:35 [DYNAMIC STABILITY CONTROL (DSC)]

DTC

C1031:35

Tire pressure monitoring system (TPMS) set switch

DETECTION

CONDITION

Continuous ON signal from the TPMS set switch for

60 s or more

is detected.

FAIL-SAFE FUNCTION

Tire pressure monitoring system warning light illuminates after

flashes.

Inhibits the TPMS control.

POSSIBLE CAUSE

The driver pressed and held the TPMS set switch for

60 s or

more

TPMS set switch malfunction

SYSTEM WIRING

DIAGRAM

—

Diagnostic procedure

STEP

INSPECTION

ACTION

VERIFY DTCs FOR INSTRUMENT CLUSTER

Switch the ignition to off.

Using the M-MDS, perform the DTC

inspection for the instrument

cluster.

(See

DTC INSPECTION [INSTRUMENT

CLUSTER]

Are any DTCs detected?

YesGo to applicable DTC inspection.

(See

DTC TABLE [INSTRUMENT CLUSTER]

No Go to the next step.

INSPECT TPMS SET SWITCH

Inspect the TPMS set switch.

(See

TIRE PRESSURE MONITORING

SYSTEM SET SWITCH INSPECTION

YesGo to the next step.

No Replace the TPMS set switch, then go to the

next step.

(See

TIRE PRESSURE MONITORING SYSTEM SET

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands