Mazda 2013 CX-5 Workshop Manual Download Page 21

Page: 21 / 223

DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2878200.html[1/7/13 9:28:47 AM]

< Previous

Next >

2013 - CX-5 - Brakes

DTC

C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01

[DYNAMIC STABILITY CONTROL (DSC)]

DTC

C0001:01, C0002:01

Traction control solenoid valve system

C0003:01, C0004:01

Stability control solenoid valve system

C0010:01

LF inlet solenoid valve system

C0011:01

LF outlet solenoid valve system

C0014:01

RF inlet solenoid valve system

C0015:01

RF outlet solenoid valve system

C0018:01

LR inlet solenoid valve system

C0019:01

LR outlet solenoid valve system

C001C:01

RR inlet solenoid valve system

C001D:01

RR outlet solenoid valve system

DETECTION

CONDITION

Malfunction detected in the DSC HU/CM solenoid valve or internal circuit by the DSC HU/CM on-

board diagnostic function

FAIL-SAFE

FUNCTION

Illuminates the ABS warning light, brake system warning light, and TCS/DSC indicator light.

Inhibits the ABS, EBD, TCS, DSC, roll over mitigation (ROM), brake assist control, and hill launch

assist (HLA), controls.

POSSIBLE CAUSE

Open or short circuit in the DSC HU/CM internal solenoid valves

Solenoid valve malfunction

SYSTEM WIRING

DIAGRAM

—

Diagnostic procedure

STEP

INSPECTION

ACTION

VERIFY SOLENOID VALVE OPERATION

Switch the ignition to off.

Connect the M-MDS to the DLC-2.

Switch the ignition ON (engine off).

Access the active command mode for the solenoid

valve using the M-MDS.

(See

ON-BOARD DIAGNOSIS [DYNAMIC STABILITY

YesGo to the next step.

No Replace the DSC HU/CM, then go to the next step.

(See

DSC HU/CM REMOVAL/INSTALLATION

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands