manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Message List

89

6

Snmp over IP over 1394 is ready.

Communication over IP over 1394 with SNMP 
is available.

Snmp over ipx is ready.

Communication over IPX with SNMP is avail-
able.

snmpd start.

SNMP service has started.

started.

Direct print service has started.

The print server received error <error 
number> during attempt to log in to the net-
work.Access to the network was denied.Verify 
that the print server name and password are 
correct. 

Cannot log in to the file server. The print serv-
er is not registered or the password is speci-
fied. Register the print server without 
specifying a password.

win2kspd protocol-DOWN (APPEXIT).

NVRAM setting ioctl (SPIO CAPPEXIT) of de-
vice SBP2TSP was set by protocol-DOWN.

SCSI print is not receiving data.

win2kspd protocol-UP (APPENTRY).

NVRAM setting ioctl (SPIO CAPPENTRY) of 
device SBP2TSP was set by protocol-UP.

SCSI print is not receiving data.

win2kspd started.

SCSI print (SBP-2) service has started.

WINS name refresh :Server No Response

There has been no response to the update re-
quest from the server. Confirm that the WINS 
server address is correct and the WINS server 
is working properly.

WINS name registration:Server No Response

There has been no response to the registration 
request from the server. Confirm that the 
WINS server address is correct and the WINS 
server is working properly.

WINS server address0.0.0.0

The WINS server address has not been speci-
fied. Specify the WINS server address to 
match the printer name with WINS.

WINS Server=< WINS server address > NetBI-
OS Name=<NetBIOS name>

The printer name has been successfully regis-
tered in <WINS server address>.

WINS wrong scopeID

The scope ID is wrong.

Specify the correct scope ID.

write error occurred. (diskfull)

The hard disk became full while the spool file 
was being written.
Wait until enough HDD space becomes avail-
able as printing proceeds.

write error occurred. (fatal)

A fatal error occurred while the spool file was 
being written.

Turn the printer off and then on. If this does 
not work, contact your service or sales repre-
sentative.

Message

Description and Solutions

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Zeka LP Programming Manual preview
LP
Brand: Zeka Pages: 54
QMS 4060 Supplementary Manual preview
4060
Brand: QMS Pages: 27
QMS 4060 Accessories Manual preview
4060
Brand: QMS Pages: 3
TallyGenicom T6212 Operator'S Manual preview
T6212
Brand: TallyGenicom Pages: 92
Seiko LTPD245D Technical Reference preview
LTPD245D
Brand: Seiko Pages: 76
A&D TM-2480 Instruction Manual preview
TM-2480
Brand: A&D Pages: 66
Kyocera ECOSYS M6035cdn Operation Manual preview
ECOSYS M6035cdn
Brand: Kyocera Pages: 31
Oki PRO511DW Setup Poster preview
PRO511DW
Brand: Oki Pages: 2
Oki ES9170 MFP Quick Start Manual preview
ES9170 MFP
Brand: Oki Pages: 92
Panduit PTR3E Operator And Technical Reference Manual preview
PTR3E
Brand: Panduit Pages: 59
Oki Microline 182 Handbook preview
Microline 182
Brand: Oki Pages: 175
Xerox VersaLink C9000 User Manual preview
VersaLink C9000
Brand: Xerox Pages: 255
Canon PIXMA MX712 Guía De Configuración preview
PIXMA MX712
Brand: Canon Pages: 22
Canon PIXMA MX512 Getting Started Manual preview
PIXMA MX512
Brand: Canon Pages: 4
Canon PIXMA MP970 Setup Instructions preview
PIXMA MP970
Brand: Canon Pages: 2
Canon PIXMA MX432 Getting Started Manual preview
PIXMA MX432
Brand: Canon Pages: 4
Canon MP560 - PIXMA Color Inkjet Function Manual preview
MP560 - PIXMA Color Inkjet
Brand: Canon Pages: 12
Canon PIXMA MX512 Guía De Configuración preview
PIXMA MX512
Brand: Canon Pages: 21

Brands by name

Popular brands

Load more brands