manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Error & Status Messages on the Control Panel

69

5

Error: Optional RAM

An error has occurred in the 
optional Memory Unit.

First, turn the power switch 
off and then on. If the message 
appears again, call your sales 
or service representative.

Turn off the power switch, Re-
place the Memory Unit, and 
then turn on the power 
switch. See "

Installing Memory 

Unit TypeC

" in the Setup 

Guide.

Turn off the power switch, re-
move the Memory Unit, and 
then turn on the power 
switch.

Note

❒

If you remove the Memory 
Unit, you must set up the 
option with the printer 
driver. If you are using 
Windows 95/98/Me, Win-
dows 2000 and Windows 
NT 4.0, see "

Installing the 

Printer Driver and Software

" 

in the Setup Guide.

❒

In this case, you might not 
be able to print complex 
print jobs.

Error: Parallel I/F

An error has occurred in the 
parallel interface board.

First, turn the power switch 
off and then on. If the message 
appears again, call your sales 
or service representative.

Full: Finisher Proof Tray

The proof tray of the optional 
Finisher SR730 is full.

Remove paper from the tray.

Full: Finisher Shift Tray

The shift tray of the optional 
Finisher SR730 is full.

Remove paper from the tray.

Full: Hole Punch Receptacle

The punch waste box in the 
Finisher SR730 is full.

Remove punch waste.

Full: Mailbox Proof Tray

The proof tray of the optional 
Mailbox is full.

Remove paper from the tray.

Full: Mailbox Tray #

The indicated output tray of 
the optional Mailbox is full.

#: tray number

Remove paper from the tray.

Full: Standard Tray

The standard output tray is 
full.

Remove paper from the tray.

Full: Waste Toner

The waste toner bottle is full 
of toner dust.

Call your sales or service rep-
resentative.

Messages

Description

Solution

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Canon MultiPASS L6000 User Manual preview
MultiPASS L6000
Brand: Canon Pages: 251
Canon MultiPASS C5500 Quick Start Manual preview
MultiPASS C5500
Brand: Canon Pages: 24
Canon MultiPASS L6000 Quick Start Manual preview
MultiPASS L6000
Brand: Canon Pages: 24
Canon Laser Class 700 Series Reference Manual preview
Laser Class 700 Series
Brand: Canon Pages: 221
Fargo Persona C25 Printer Selection Manual preview
Persona C25
Brand: Fargo Pages: 6
Fargo DTC4500e User Manual preview
DTC4500e
Brand: Fargo Pages: 90
Fargo DTC1000 User Manual preview
DTC1000
Brand: Fargo Pages: 126
FARGO electronics FARGO DTC 400 User Manual preview
FARGO DTC 400
Brand: FARGO electronics Pages: 278
Oki Okipage8z Limited Warranty preview
Okipage8z
Brand: Oki Pages: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Brand: Olivetti Pages: 179
Olivetti JS-505 Service Manual preview
JS-505
Brand: Olivetti Pages: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Brand: Oki Pages: 679
Oki PRO511DW Manual preview
PRO511DW
Brand: Oki Pages: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Brand: OKIDATA Pages: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Brand: OKIDATA Pages: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Brand: Oki Pages: 12
Wasp WPL608 Quick Start Manual preview
WPL608
Brand: Wasp Pages: 2

Brands by name

Popular brands

Load more brands