manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

UNIX Configuration

28

1

Staple

Select the staple position for the output.

Limitation

❒

Before executing staple, make sure the number of the collated sets and the
output tray for staple are specified.

❒

When using this option, the optional Finisher Unit is required.

❒

When printing with this option, be sure to specify the optional Finisher Unit
using the value of “finishershift”. For more information about the optional
Finisher Unit, see p.22 “Output Tray” . 

staple=

value of staple position

The following sample shows how to print with staple on the upper left using
Tray Finisher Unit 1 (host name : nphost, file name : file1).
• rsh

% rsh nphost print staple=lefttop,outbin=finishershift <
file1

• rcp

% rcp file1 nphost:staple=lefttop,outbin=finishershift

• ftp

ftp> put file1 staple=lefttop,outbin=finishershift

Staple Position

Value

Left Top

lefttop

Right Top

righttop

Not Staple

off

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

SPRT SP-T6 User Manual preview
SP-T6
Brand: SPRT Pages: 28
Oki C3000 Series Manual preview
C3000 Series
Brand: Oki Pages: 62
TallyGenicom LA800 User Manual preview
LA800
Brand: TallyGenicom Pages: 144
Xerox WorkCentre Pro 40 Specification preview
WorkCentre Pro 40
Brand: Xerox Pages: 14
Magicard Tango 2e Brochure preview
Tango 2e
Brand: Magicard Pages: 2
Magicard Tango 2e Quick Start Manual preview
Tango 2e
Brand: Magicard Pages: 2
GE TermiNet 300 Beginner'S Manual preview
TermiNet 300
Brand: GE Pages: 16
Xerox 7300DX - Phaser Color Laser Printer Specification preview
7300DX - Phaser Color Laser Printer
Brand: Xerox Pages: 14
Ricoh Aficio 3224C Service Manual preview
Aficio 3224C
Brand: Ricoh Pages: 781
Konica Minolta bizhub C654e Specification & Installation Manual preview
bizhub C654e
Brand: Konica Minolta Pages: 32
YAEN POS58C1 User Manual preview
POS58C1
Brand: YAEN Pages: 4
BenQ CM3700 Series User Manual preview
CM3700 Series
Brand: BenQ Pages: 6
Lexmark C782dn Reference Manual preview
C782dn
Brand: Lexmark Pages: 4
Oki C831dn Safety And Warranty Manual preview
C831dn
Brand: Oki Pages: 48
Xerox WorkCentre 7200 series Specifications preview
WorkCentre 7200 series
Brand: Xerox Pages: 12
Oce im3530 Operator'S Manual preview
im3530
Brand: Oce Pages: 186
Xerox DocuPrint C6 User Manual preview
DocuPrint C6
Brand: Xerox Pages: 78
Ricoh Aficio SP 3300D Specification Sheet preview
Aficio SP 3300D
Brand: Ricoh Pages: 2

Brands by name

Popular brands

Load more brands