Home
/
Lanier
/
AP4510
/
Setup Manual

Lanier AP4510, Setup Manual

Share

Page: 192 / 424

background image

Making Printer Settings with the Control Panel

118

6

Output Tray

You can select the default output tray.

Standard Tray, Finisher Shift Tray, Finisher Proof Tray, Mailbox
Proof Tray, Mailbox Tray 1-9

Note

❒

Default: Standard Tray

❒

Only the installed trays appear on the panel display.

Job Separation

You can enable Job Separation.
• On

• Off

Note

❒

Default: Off

❒

This menu appears only when the optional Finisher is in-
stalled.

Energy Saver

You can set how many minutes the printer waits before switching
to Energy Saver mode. Energy Saver mode reduces electric power
consumption.

On, Off
1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 min-
utes,

Note

❒

Default: On

❒

Default: 1 minute

❒

If there is an error in the printer, the printer will not turn into
Energy Saver mode.

❒

When the printer switches to Energy Saver mode, the

Power

indicator turns off, while the

On Line

indicator stays on.

Memory Usage

You can select the volume of memory to be used from "Font Pri-
ority" or "Frame Priority", according to the paper size, resolution
or printer language.

• Font Priority

This setting uses memory for registering fonts.

• Frame Priority

This setting uses memory for high speed printing.

Note

❒

Default: Frame Priority

Reference

For more information, see p.136 “Paper Size and Resolution”.

Unit Of Measure

You can select "mm" or "inch" for the custom paper size.

Menu

Description

«
...
190
191
192
193
194
...
»

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Brand: Oki Pages: 152

Brand: Oki Pages: 140

Brand: Oki Pages: 181

Brand: Oki Pages: 52

Brand: Oki Pages: 229

Brand: Oki Pages: 224

Brand: Oki Pages: 141

Brand: Oki Pages: 160

Brand: Oki Pages: 48

Brand: Oki Pages: 20

Brand: Oki Pages: 52

Brand: Oki Pages: 127

Brand: Oki Pages: 128

Brand: Oki Pages: 12

Brand: Oki Pages: 41

Brand: Oki Pages: 35

Brand: Oki Pages: 165

Brand: Oki Pages: 262

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands