Home
/
Lanier
/
AP4510
/
Setup Manual

Lanier AP4510, Setup Manual

Share

Page: 250 / 424

background image

Windows 95/98/Me Configuration

10

1

Setting Up a Client Computer

This section describes the procedures for setting up a client on a network that
uses Windows 2000, Windows NT Server or Windows NT Workstation as a
print server.
When using a Windows 2000 or Windows NT print server, select a shared print-
er on Windows 2000 or Windows NT.

Limitation

❒

When using a print server connected to the printer with Ridoc IO Navi, you
cannot use Recovery Printing.

Note

❒

This section assumes that the client has already been configured to communi-
cate with a Windows 2000 or Windows NT print server. Do not begin the fol-
lowing procedure until the client has been set up and configured correctly.

AAAA

Install the printer driver as a local printer.

Reference

For more information about installing the printer driver, see the Setup
Guide.

Note

❒

Any port can be selected during the installation, however, LPT1 is recom-
mended.

BBBB

Click

[

Start

]

, point to

[

Settings

]

, and then click

[

Printers

]

.

CCCC

Click the icon of the printer you want to use. On the

[

File

]

menu, click

[

Prop-

erties

]

.

Windows 2000 or
Windows NT Print Server

Windows 95/98/Me

«
...
248
249
250
251
252
...
»

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

iPF650 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 40

iP90 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

iPF650 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 16

iP100 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

imageRUNNER ADVANCE C5560

Brand: Canon Pages: 67

imageRUNNER 3300

Brand: Canon Pages: 366

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 252

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 2

Brand: BadgePass Pages: 2

Brand: Oki Pages: 572

proColor pro900DP

Brand: Oki Pages: 127

Brand: Olivetti Pages: 309

Brand: OKIDATA Pages: 4

Brand: Canon Pages: 37

Brand: Oki Pages: 24

Brand: Pantum Pages: 115

Brand: Xiamen Hanin Electronic Technology Pages: 62

WorkCentre Pro 32

Brand: Xerox Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands