manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

61

5. Macintosh Configuration

Configuring Macintosh

This section describes how to configure a Macintosh computer to use EtherTalk.
The actual procedures to configure a Macintosh may vary depending on the ver-
sion of the Mac OS. The following procedure describes how to configure Mac OS
9.1. If you are not using Mac OS 9.1, see the manual that comes with your version
of Mac OS for more information.

Changing to EtherTalk

The following procedure is for configuring a Macintosh computer to use
EtherTalk.

Reference

For more information about installing the software required for EtherTalk,
see the Macintosh manuals.

AAAA

Open 

[

Control Panel

]

, and then double-click the 

[

AppleTalk

]

 icon.

BBBB

From the 

[

Connect via:

]

 pop-up menu, select “Ethernet”.

CCCC

If you change zones, select a name from the 

[

Current zone:

]

 pop-up menu.

DDDD

Close the 

[

AppleTalk

]

 control panels.

EEEE

Restart the Macintosh.

Change to EtherTalk

Basic Procedure

Configure the printer

Change the printer name

Change the zone

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Canon MX490 Series Setup Manual preview
MX490 Series
Brand: Canon Pages: 11
Canon MX490 Series Quick Help Manual preview
MX490 Series
Brand: Canon Pages: 2
Canon Photura 135 Review preview
Photura 135
Brand: Canon Pages: 12
Canon PIXMA Pro9000 Mark II Series Release Note preview
PIXMA Pro9000 Mark II Series
Brand: Canon Pages: 4
Dascom TALLY MIP480 User Manual preview
TALLY MIP480
Brand: Dascom Pages: 138
Dascom T2150 User Manual preview
T2150
Brand: Dascom Pages: 166
idp SMART-30R User Manual preview
SMART-30R
Brand: idp Pages: 88
Radio Shack DMP-200 Operation Manual preview
DMP-200
Brand: Radio Shack Pages: 62
Lexmark S510 Series Quick Reference Manual preview
S510 Series
Brand: Lexmark Pages: 59
Oce DFS10 Operator'S Manual preview
DFS10
Brand: Oce Pages: 90
Xante FilmMaker 4 Quick Reference Manual preview
FilmMaker 4
Brand: Xante Pages: 31
MAC TOOLS P 9300 Instruction Manual preview
P 9300
Brand: MAC TOOLS Pages: 2
Lexmark Monochrome Laser Installation Sheet preview
Monochrome Laser
Brand: Lexmark Pages: 1
Protech Systems MP-1060 User Manual preview
MP-1060
Brand: Protech Systems Pages: 140
Xerox 8200DX - Phaser Color Solid Ink Printer Manual preview
8200DX - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 2
Konica Minolta bizhub 215 Installation Manual preview
bizhub 215
Brand: Konica Minolta Pages: 8
Savin 4035e Copy Reference Manual preview
4035e
Brand: Savin Pages: 132
Lexmark Pro900 Series Installation Instructions Manual preview
Pro900 Series
Brand: Lexmark Pages: 10

Brands by name

Popular brands

Load more brands