manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Windows NT 4.0 Configuration

28

3

BBBB

Configure the TCP/IP protocols with the appropriate IP address, subnet
mask and other settings.

Check with the network administrator that the settings are correct.

CCCC

Click the 

[

Services

]

 tab, and then make sure that “Microsoft TCP/IP Print-

ing” is installed.

If “Microsoft TCP/IP Printing” is not installed, click 

[

Add

]

 on the 

[

Services 

]

tab, to install it. For more information about installing and configuring net-
work services, see Windows NT Help.

Configuring NetBEUI for Printing

These instructions are for configuring the Network Interface Board and Win-
dows NT to use the NetBEUI protocol.

Configuring the machine

Configure the machine to use the NetBEUI protocol.
• Make sure that the NetBEUI protocol is set to active. (The default is active.)

Reference

For more information about how to make the above settings, see the Setup
Guide.

Configuring a Windows NT computer

Install the NetBEUI protocol on the Windows NT computer, and then change the
LAN adapter number (Lana Number).

AAAA

Open 

[

Control Panel

]

, and then double-click the 

[

Network

]

 icon. Make sure

that “NetBEUI Protocol” is listed in the 

[

Network Protocols

]

 box on the 

[

Proto-

cols

]

 tab.

Note

❒

If the NetBEUI protocol is not installed, click 

[

Add

]

 on the 

[

Protocols

]

 tab to

install it. For more information about installing the NetBEUI protocol, see
Windows NT Help.

BBBB

Change the Lana Number. Click the 

[

Services

]

 tab, click “NetBIOS Inter-

face” in the 

[

Services

]

 tab, and then click 

[

Properties

]

.

CCCC

Click the Lana Number corresponding the Nbf protocol of the 

[

Network

Route

]

 headline, and then click 

[

Edit

]

.

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Lexmark S510 Series Quick Reference Manual preview
S510 Series
Brand: Lexmark Pages: 59
Canon PIXMA TR4720 Online Manual preview
PIXMA TR4720
Brand: Canon Pages: 542
Xerox WorkCentre PE120i Evaluator Manual preview
WorkCentre PE120i
Brand: Xerox Pages: 8
AstroJet IB-9000-6P Operator'S Manual preview
IB-9000-6P
Brand: AstroJet Pages: 32
Xerox DocuPrint 96 IPS Series System Overview Manual preview
DocuPrint 96 IPS Series
Brand: Xerox Pages: 101
Olivetti d-Copia 164MF Operation Manual preview
d-Copia 164MF
Brand: Olivetti Pages: 97
Epson AcuLasaer C1900 Quick Reference Manual preview
AcuLasaer C1900
Brand: Epson Pages: 17
Epson 3880 - Stylus Pro Color Inkjet Printer Specifications preview
3880 - Stylus Pro Color Inkjet Printer
Brand: Epson Pages: 2
Epson AcuLaser CX11NF Fax Manual preview
AcuLaser CX11NF
Brand: Epson Pages: 64
Epson AcuLaser CX11N Basic Manual preview
AcuLaser CX11N
Brand: Epson Pages: 144
Epson AcuLaser CX16 Quick Manual preview
AcuLaser CX16
Brand: Epson Pages: 193
Epson AcuLaser C2900N Safety Information Manual preview
AcuLaser C2900N
Brand: Epson Pages: 342
Epson AcuLaser CX11NF Specifications preview
AcuLaser CX11NF
Brand: Epson Pages: 2
IBM Network Printer 12 User Manual preview
Network Printer 12
Brand: IBM Pages: 224
ICOD T58Z User Manual preview
T58Z
Brand: ICOD Pages: 28
XITRON Prism Setup Manual preview
Prism
Brand: XITRON Pages: 24
Oki MB780 Service Manual preview
MB780
Brand: Oki Pages: 41
BEINAT STM001 User Manual preview
STM001
Brand: BEINAT Pages: 4

Brands by name

Popular brands

Load more brands